In the low setting, the 5th wheel is 3" nose high, which is still acceptable, though more level is preferred to keep pressure off the rear axle * My truck has Auto-Level Air suspension so I can lower it 1" to keep the front of the 5th wheel more level. This yields about 9" from bedrail to under side of the 5th wheel overhang. * I started out with the Andersen ball in the highest position to ensure maximum bed rail clearance on deep turns. Cougars typically have trimmed lower front-cap corners that help clear the cab * My 5th wheel is a Cougar 30RLS, half-ton series. * The cup position also improves the gap between the rear of the pinbox and the bed rails of the RAMBox bed, which is the main consideration in this scenario. * The Andersen cup is mounted on the pin to give maximum cab clearance (cup to rear of pin) There are some specific things that help this work for my rig that might not work for others: Other pin boxes that extend downward would likely work even better than my setup. My trailer's frame is a Lippert 1620 with a RotaFlex pinbox. The 3200 is rated for 4200 lb pin weight and 20,000 lb trailer weight (depending on your trailer, this may not be enough load capacity). I also installed a Curt 5th wheel 7 pin connector (C56070) in the bed, got to be careful with the location with a RAMBox bed but it looks OE and works great. The combination is much lighter than a typical 5th wheel hitch and breaks down quickly and separately for easy removal/installation. This let me use a Reese Rail Kit (30154) to mount the Anderson 3200 in. Can't get 5th wheel prep or gooseneck prep in a RAMBox truck so I installed the OEM puck system (82215838AB) myself. If you have any questions, please contact us via chat or by phone at 88.I know not everyone is a fan and most folks are not convinced it can work but I thought I'd pass along my set up with an Anderson 3200 hitch (steel not aluminum). All hardware, washers, and threaded inserts are included with your purchase. Installation of this Bed Rack is considerably straight forward and can typically be completed within hour. The upTOP TRUSS RamBox Compatible Bed Rack system was designed with the consumer in mind.
The upTOP TRUSS system come complete with load bearing armor plates that bolt to each side of the rack.
Rambox bed rack forum full#
The versatility doesn't stop with the TRUSS fitment however, as the crew at upTOP Overland had it in mind during the full engineering process. This allows the truck owner to fine tailor his rack to best fit his lifestyle. Not only is the upTOP TRUSS RamBox Compatible Bed Rack available for a short or long bed RAM's, you also have the ability of choosing to receive a mid-height (11.5') or full-height (22.5") rack.
One thing that should quickly stand out about upTOP's Bed Rack over the competition is how versatile it truly is. In addition, your upTOP TRUSS RamBox Compatible Bed Rack will receive a stealth black powder-coat finish to ensure rust and corrosion resistance. To further establish optimum strength and durability, each component of this product is bent, formed, and welded. 250” aluminum construction, providing you with the perfect combination of strength and reduced weight. This product page is dedicated to the upTOP TRUSS RamBox Compatible Bed Rack.Īs the name implies, the upTOP TRUSS RamBox Compatible Bed Rack has been designed to work exclusively with your RAM's equipped with a RamBox bed. Between its quality craftsmanship and versatile design, the upTOP Bed Rack is sure to get the job done. The upTOP TRUSS Bed Rack is quite arguably one of the most well-built bed racks on the market at this time. Proudly designed and fabricated right here in the U.S.A.Load bearing armor plates accommodate the mounting of your favorite cargo and gear such as MAXTRAX, RotopaX, Quick Fists, Waterports, and much more.Available for both short bed and long bed rigs Choose between a mid-height (11.5") or full-height (19") option.Designed to work exclusively with the 2009+ RAM 2500/3500 w/ Rambox.
0 kommentar(er)
